Condensing steam boiler can be favored by many enterprises because of its energy-saving, environmental protection and tolerance, and has gradually become one of the most popular boiler products in boiler products. The heat-resistant and wear-resistant condensing steam boiler needs to produce a large amount of steam through water, so it is necessary to inject a large amount of water into the equipment during operation. Because the equipment requires strict operation of boiler water filling, it needs to be operated according to the standard before it can be used normally. The condensing steam boiler equipment should pay attention to when feeding water to the equipment and see the following brief description:
1: in order to prolong the service life of the boiler, the condensing steam boiler reduces the occurrence of precipitation in the furnace in order to prolong the service life of the equipment and reduce the occurrence of precipitation in the furnace due to the different properties of the different water quality and the different precipitated substances. Therefore, the use of water quality has certain requirements and can choose the applicable water quality, which can improve the service life of boilers and reduce the production of a large amount of water scale. There are certain requirements for the use of water is not any kind of water can be used, in order to effectively protect the service life of boilers should pay attention to the selection of water suitable for the water quality requirements. And the water used must be soft water that has been tested and treated so that it does not produce a large amount of water. The long-term accumulation of dirt in the boiler causes pollution to affect the quality of use.
2: there are relevant standards for water temperature control during the operation of condensing steam boilers. Users should pay attention to controlling the water temperature within the standard range in order to achieve good use without anomalies. If the water temperature is too high, the high expansion of the whole equipment will cause the pipe to leak, and the low water temperature will make the steam production not enough to meet the normal use requirements of the enterprise.
3: when adding water to a condensing steam boiler at the standard level, attention should also be paid to the standard water level, which should not exceed the height of the water mark in order to ensure safety in use. Higher than the water level will not only cause waste but also cause the equipment to expand. When the expansion reaches the limit of the water level, it will cause the water to spill out and waste or even shorten the service life of the equipment.
Gas fired steam boiler pressure is not on what causes? Gas fired steam boiler is not very common on the pressure, the main cause of 1, if the pump is working properly. 2, the pressure gauge is broken. 3, the check valve is blocked. 4, whether to reverse the induced draft fan. Mainly caused due to the above four reasons. Users have been asking how to burn gas steam boiler do not increase the pressure, there are a lot of factors, and today we talk about a few of these factors. First, check to see if the pump work, can achieve much pressure pump, pump installation is going to be a pressure gauge installed in the pump above, this is because, if the increase to no water inside the steam boiler can detect whether it is caused by reason of the pump . Pressure gauge to detect what is not broken. Check whether the induced draft fan reverse, users have encountered this situation, the beginning is very anxious to buy gas fired steam boiler has been not on the pressure, so he checked the pump, check valve, no problems, after his inspection induced draft fan is not inverted, after examination revealed induced draft fan power line reversed, and after adjusting all normal. After the situation encountered gas steam boiler is not burning on the pressure do not worry, first check the steam boiler attachment which is not connected to the wrong place or method of operation requires no installation operations, after then contact technical personnel.
The low nitrogen combustion technology has been invented to upgrade to make the low nitrogen boiler retrofit meet the relevant requirements has become a lot of manufacturers are actively preparing and executing things, in Xi'an low nitrogen boiler renovation bidding professional institutions with very high professional level, The low nitrogen boiler reconstruction construction scheme issued by these institutions can quickly respond to the needs of optimization and upgrading of all kinds of boilers, so what are the key points to be paid attention to when carrying out the low nitrogen boiler transformation?
1, it is a process of mechanical and technical transformation and environmental upgrading that requires qualified institutions to complete the retrofit of low-nitrogen boilers. Then, when reforming the low nitrogen boiler, we should ask the organization with the specialized technology and qualification to complete it. The specialized low nitrogen boiler retrofit company can give the standard and reasonable transformation with the excellent technical strength and rich experience.
2, to do a good job in the safety management during the renovation period, the main point that must not be sloppy in the whole process of the actual transformation of the low nitrogen boiler is to pay attention to the safe and smooth upgrading of the boiler. At the same time, it is necessary to take into account the personal safety protection of all participants and the maintenance of the equipment core during the renovation and upgrade period, and all upgrading and retrofitting actions should be carried out in accordance with the form of expert norms.
3, another key point of the revamping operation of the low-nitrogen boiler is to do a good job in the observation of the equipment hoisting after the transformation, mainly to carry out omni-directional state inspection on the boiler core functional areas after the transformation. Then the equipment operation of low nitrogen boiler was observed in a scientific way.
It is understood that the main purpose of this research group is to study the production and operation of special equipment safety in our province, our city as a leader in the field of industrial and special equipment production areas of well-known companies has been the concern of the research group. After the tour, the research group said it would I recommend the best practices for future sample safe production, operation and management of special equipment, I also hope that the company's future and make greater achievements and contributions in the field.Free Chat
Copyright © 2020.Company name All rights reserved.