Gas boiler cost transformation precautions so that your boiler is more successful transformation: in our country under the frequent introduction of environmental policies, many units use coal-fired boilers or other fuel boilers are faced with the situation of the boiler. Provinces for the introduction of atmospheric emissions policy, boiler "coal to gas" imminent.
A number of factors cause the pressure of the heat efficiency of the boiler cost module are carrying substantially all parts of the coal gas impressive work, use a large extent, avoided the module boiler fouling contamination, while discharging hazardous gas like nitrogen oxides obtained a clamp. Thermal efficiency is an important measure of the rule module boiler, let us study the cause of a number of factors under the pressure of the thermal efficiency of the boiler module. After inquire about the personnel, boiler heat loss module is mainly produced in the bear on these two: the proportion of full combustion air with smoke emission unreasonable heat loss. Reduce smoke emission install heat loss can be recovered in the flue gas waste heat boiler module terminal fitting, or use more advanced features of FGR boiler. The combustion air fully proportional unreasonable non-compliant analysis: General ejector module boiler burner, causing the air-fuel ratio is no way to maneuver to mobilize. Part of the boiler module using a mechanical blower burner, resulting in unreasonable cause fuel ratio factors are the following: the main air-fuel ratio unreasonable encompass divided into two cases: when oxygen is excessive, the excess will be numerous cold is heated, resulting in increased cost of energy boiler module, the thermal efficiency of the boiler module lowered; when oxygen is non-compliance, will produce incomplete combustion occurs module boiler heat efficiency is lowered.
Diqing in Yunnan Nonferrous Metals Co., Ltd. mainly engaged in Pulang copper mining, site selection, sales and other items. As we all know, in the copper smelting process, it consumes a lot of electricity and thermal power resources, which account for most of the hot water consumption. Combined with the actual demand Diqing company, to provide fast Boiler 1 stage electric heating hot water boiler cost of 2.1MW.
Gas boiler cost heat loss through the combustion of fuel gas boiler, will release some heat, which will supply part of the user, some will be recycled and part is inadvertently wasted. So these are wasted heat lost through the ways in which it (1) heat losses:? Flue gas exhaust gas boiler part of the heat into the atmosphere, causing the boiler heat losses, it is each boiler term heat loss Dazhong biggest one. The main factors influencing the heat loss is higher exhaust gas temperature and the amount of smoke exhaust gas temperature, the greater the amount of smoke, the greater the heat loss. Low exhaust gas temperature depends mainly on the number and operating conditions of the heating surface; the amount depends on how much leakage exhaust case and the furnace excess air, flue. (2) heat loss incomplete combustion gas: a part of the unburned combustible gas is discharged with the flue gas to heat loss caused by heat in the flue gas. The main factors affecting the incomplete combustion gas heat loss is the excess air and furnace structure. Excess air coefficient is too small, uneven air is mixed with fuel, easy to generate carbon monoxide and other combustible gases; excess air coefficient is too large, the furnace temperature is lowered, the combustible gas is not easy ignition and combustion. Furnace volume is too small, combustible gases in the furnace too late to enter the combustion flue gases caused by incomplete combustion heat loss. (3) heat loss: the furnace heat loss, frameworks, pipes, door opening caused by heat dissipation to the surroundings. Size depends on the heat loss factors of the size of the surface area of the furnace gas steam boiler, heat insulating properties and thickness, the outside air temperature and the flow velocity. Electric heating reactor common external damage: an electrically heated reactor despite external corrosion has a high etching resistance against acid and alkali resistance, but our electrical heating by the heating apparatus is a kettle layer and an outer tire iron constituted. Such a medium is iron acids and bases are not corrosion-resistant. If we would have the production process if the reactor cover or screwed pipe joints without seal failure or leak acid tire iron reactor apparatus for electrically heating the outer corrosion. Corrosion support member 2. The reactor was heated electrically heated reactor during installation, support or other support member may be mounted directly on the floor, due to the long manufacturing operations on the floor may be deposited with corrosive media, so that for support our reactor electrically heated apparatus corrosion, resulting in the supporting force of each of the support produces a change resulting in a change in stress in the damage produced during heating layer. 3. The electrically heated reactor stress spout in the electrically heated reactor, when the steel of the pipe and the pipe joint, since the thermal deformation and the reaction was heated electrically heated autoclave vessel or duct stressed cold might damage the pipe.Free Chat
Copyright © 2020.Company name All rights reserved.