Gas oil furnace fuel additive effect and the crude fuel steam output boiler cost room Notes: Gas oil furnace, oil furnace that is both in one, and, still in the boiler in this category, so, based on this, the following will continue be familiar with and understand the boiler, because it is the product website and keywords. Moreover, we can also derive some new knowledge, in turn, make progress and development in their learning path. 1. Gas oil furnace, which is a fuel additive, then what good? Gas conducting oil furnace, in which fuel additives, it is possible to optimize the fuel, and reducing soot and improving thermal efficiency. However, it should be noted that, in addition amount to control the well, in moderation, too much or too little, will always have problems, thereby, affecting the normal combustion of the fuel. 2. Gas-fired steam boiler and gas oil furnace, boiler room can both jointly built it? Gas-fired steam boiler and gas oil furnace, two boiler room, is jointly built, and that is no problem. However, it should be carried out in accordance with the steam boiler room equipment specifications and oil furnace room design specifications, avoid mistakes, and at the same time, to make the two boilers, a good use of effects.
It is understood that around prevention and control of air pollution, ecological Environmental Protection Office of Shaanxi Province has formulated the "Boiler Air Pollutants Emission Standards" ( "Standards"), amended the "off key industries in the region of atmospheric pollutant emission limits." In the future, biomass, alcohol fuel crude fuel steam output boiler cost emissions also be included in "Standards".
"Standard" is to integrate and improve the local air emissions standards boilers. "Standard" for the scope of the province, covering coal, gas, oil, various types of fuel such as biomass; using alcohol fuel (e.g., methanol, ethanol, dimethyl ether, etc.), gas-fired boiler with reference to the implementation of emission limits.
After calculation, coal-fired thermal power boilers in Shaanxi Province implementation of the new standards, particulate matter, sulfur dioxide, nitrogen oxide emissions respectively about 0.67 tons 15,200 tons, 1.26 tons, down 27%, 40%, 21%; Burning after transformation of coal boiler, particulate matter, sulfur dioxide, nitrogen oxide emissions can be about 01,400 tons, 1.42 tons 14,100 tons.
With the haze pollution reduction work to promote strong, Shaanxi Province coal-fired generating units and 20 steam tons / hour or more coal-fired boiler to carry out the transformation of ultra-low emissions, will gradually iron and steel, cement and other industries to carry over non-electric low-emission transformation, the original standard has been overtaken by change of environmental situation. Additionally, the Guanzhong area of glass, ceramics, bricks, gold and other industry, there are a certain number of kiln, its environmental requirements leniency.
The revision of the "off key industries in the region air pollutant emission standards", the abolition of the thermal power industry, coal-fired boiler emission limit requirements, these two sectors rose to individual standards province-wide.
It also increases the coke nitrogen oxide emission limits Chemical Industries, gold industry, glass and glass products, ceramic industry emission limits, increasing the concentration of tile industries and atmospheric pollutants conversion approach.
The new standards are expected coke chemical industry NOx emissions will decrease 70%, the sintering process the steel industry, the particulate matter, SO2, NOx emissions decreased by 50%, 72% and 67%, respectively.
Gas crude fuel steam output boiler costs and oil-fired boilers and oil-fired boiler gas boiler difference is we will use in industrial boiler, although only one word, but what difference does it both? Xiao Bian today to introduce you to the difference between the gas boiler and boiler fuel: fuel oil-fired boiler is fuel such as diesel, oil, kerosene, fuel gas-fired boiler to gas such as natural gas, city gas, methane, etc., depending on the boiler fuel What devices called fuel burner, gas burner configuration called boiler gas boiler, oil boiler burner configuration called oil-fired boiler, oil-fired boiler and gas boiler difference is that what fuel burners. Construction of boiler body is the same reason, need more thick steel plate with built-in boiler tubes are the same. The fuel gas boiler can be divided into natural gas, city gas, coke oven gas, liquefied petroleum gas and biogas, according to the function can be divided into water boilers, hot water boilers, heating stoves, heating stove, steam boilers, environmental protection boiler, bath boilers, bridge dedicated boiler, waste heat boiler, in accordance with the configuration it may be divided into vertical gas boiler, gas boiler horizontal; in accordance with the flue gas flow can be divided into three single backhaul backhaul gas boiler and gas boiler. Learn the difference between gas boilers and oil-fired boiler, I believe you must be the same as with Xiaobian learned a lot of knowledge, I hope this can help you better buy boiler equipment
Electric heating steam crude fuel steam output boiler cost Products electric heating steam boiler is the electrical energy into heat of a new type of electric equipment, following the same "boiler Safety Supervision" and the manufacturing industry standard in design. By electric heating equipment, heating equipment consisting of furnace, safety accessories, strong, weak control systems and other components all have national compulsory safety certification mark. Full immersion heating elements fixed to the flange, easy to change freely. Circuit design using fuses, electrical harmonics are controlled to ensure effective protection of the safety of the power supply circuit. Boiler power control system using a host and a separated manner, to avoid disturbing the electrical and thermal aging electrical components. Product description features: ① may provide a direct product structure analysis, gas-assisted technology application support, precision molds (gas assisted mold), plastic products (gas assisted products), heat distortion temperature trace full service support molding technology; ② can be provided directly in the gas-assisted injection molding technique involves analysis of the product, mold design, optimization support mold, gas-assisted manufacturing mold, gas-assisted process support, a reasonable selection, and other gas-assisted equipment; many enterprises effective use of gas-assisted technology to enhance the quality of products, reduce production costs provide a strong technical support. ③ may be provided directly to all sets of gas-assisted injection molding system devices patents involved in the development of the company designed the special requirements for gas-assisted production, production and closely monitor, such as high reliability of compressed air purification system, maintenance-free three-year nitrogen separation system, the introduction of foreign produce high quality clean diaphragm high pressure compression system (compression pressure nitrogen completely solve the hidden oil contamination), and gas-assisted pressure control with high precision: the temperature change may provide direct heat trace technique involves molding All patents sets of equipment, including steam-assisted injection molding equipment, electric assisted molding apparatus, hot water and hot oil auxiliary molding equipment accessory, ④ may be provided directly GAIM equipment, heat molding temperature change trace all the technical equipment involved service, spare parts service, customers do not need to face before other vendors run the preparatory work: (1) the operator must know the location of the working principle of the boiler, all kinds of accessories, performance and working methods. (2), check the oil combustion, and each nozzle connection, power supply and the burner, the pump, the boiler installation accessory. (3), a clear main steam valve open, after closing the normal close it. (4), water level gauge inspection, confirmation flexible water level, normal position. (5), the pressure regulator is properly tuned, regulate combustion damper.Free Chat
Copyright © 2020.Company name All rights reserved.