Assembled Oil Fuel Steam Boiler

Assembled Oil Fuel Steam Boiler

Gas-fired heating is to protect human health and indoor warm natural gas boiler with natural gas, LPG, city gas and other gaseous fuels for fuel combustion in the furnace put out heat, heat the pot of water, and it vaporized into steam the thermal energy conversion device. Water pan (drum) is continuously released from the combustion of a gaseous fuel energy to heat the furnace temperature is increased and produce steam under pressure. Since the boiling point of water increases with increased pressure, the pot is sealed, the expansion of water vapor generated inside the pressure limited thermodynamic formed, strictly speaking, the assembled fuel steam boiler is heated in water at constant pressure saturated steam drum regasification water formed, is widely used as an energy source. Gas-fired heating is to protect human health and indoor warm, so the choice of natural gas boiler when security issues are important, but the quality can not be ignored, and only with good quality, just more comfortable when in use, some of the services also can do better, choice of heating is customer satisfaction. Learn natural gas boiler certainly need to know the sales of the product, and if it shows good reputation natural gas boiler in the comprehensive aspects are still very good, worthy of consumer choice, performance, and thermal energy conversion can consult, when such use was not there will be problems when installed, do not worry voltage is not enough. Gas boiler shutdown method: after stopping a powder, a duct for 5 minutes and then purged to stop the gun. Oil gun should be purged one by one, not at the same time purging multivessel oil gun. After completion of purging gun oil, natural ventilation of the boiler furnace 5 to 8 minutes, 20 ~ 30% of the air volume is not less than the rated load. To exclude combustible material remaining in the furnace. The fuel gas-fired steam boiler can be divided into natural gas, city gas steam boiler, a steam boiler coke oven gas, LPG and steam boiler; according to the structure can be divided into vertical and horizontal steam boiler steam boiler. Gas boiler shell type three return all wet back downstream pyrotechnic pipe structure, the combustion flame in the combustion chamber large positive pressure, fully extended, low combustion heat load, the high heat of combustion efficiency, effectively reducing the exhaust gas temperature, energy saving , more economical, and a waveform furnace threaded pipe structure, i.e. increase the strength of the heat absorption of the boiler, but also to meet the needs of thermal expansion of the heating surface, scientific and rational, and durable.

High resistance assembled fuel steam boiler gas handling system: 1, gas steam boiler pressure gauge, water level gauge, safety, sewage, a water supply valve, a steam valve, check whether the performance requirements, other valves in good condition. Gas hot water boiler with environmental protection, energy conservation, safety, salient features fully automatic operation, and ease of use. In addition, due to the operation of the economy, government policies to encourage, gas hot water boiler more and more people of all ages. Steam boiler is an energy conversion device, the energy input to the boiler fuel chemical energy, electrical energy, thermal energy and other forms of high temperature flue gas, and after converting the boiler, the steam output having a certain outside thermal energy, high-temperature hot water or an organic carrier. 2, the boiler Zidongkongzhi device system, comprising a flame detector, level, temperature detection, a variety of interlocks and alarm means, display control system performance states to meet the requirements. Biomass boiler categories: biomass boilers Horizontal, vertical biomass boilers. Biomass gas thermal oil heaters, biomass steam boiler, biomass hot water boiler, biomass oil furnace.

In recent years, the state environmental protection is all the more attention we as a company with the times, in order to respond positively to the implementation of the national environmental protection requirements from coal to gas project. But the choice of boiler suppliers in this area quite a headache, after repeated comparison and investigation, we chose to partner with fast boiler. Fang did not disappoint quickly proved that the recommended boiler operation after use to fully meet our needs, both energy saving and environmental protection, high thermal efficiency, to a certain extent, cost savings for our fuel. --customer feedback

What are the precautions in the loading and installation of gas-fired assembled fuel steam boilers?

Gas-fired steam boilers are a very wide range of special equipments, widely used in food, chemical, paper, textile, construction and other industries. In the process of loading and installing a gas steam boiler, some problems must be paid attention, otherwise it may cause a certain degree of economic loss.

1. Pay attention to the following matters during the loading and unloading and handling of gas-fired boilers: the lifting capacity of the lifting equipment should match the weight of the lifting boiler. The lifting lug on the boiler with the lifting lugs that cannot be used for lifting can not be used for lifting. The length of the steel cord should be reasonably selected to avoid the scratching of the furnace due to the improper length of the steel cord. The boiler must be protected from any damage during handling and handling.

2. Reserves for maintenance space When installing boilers, ensure that there is sufficient maintenance space around the boiler.

3. Setting and precautions for the base and base of the gas steam boiler The boiler body must be installed on the basis of 100-150mm above the floor of the boiler room. It must be confirmed with the technical personnel of the boiler manufacturing company in advance and constructed according to the basic drawings. The anchor bolts must be reserved on the foundation. The foundation shall be capable of withstanding the maximum weight of the boiler and the amount of water it holds. When installing the base, you must first position it. After positioning, adjust to the same length of the two diagonals of the base, and then tighten all the fixing bolts. The installation of the base is carried out with reference to the reference line.

4, general precautions Be careful not to tilt and impact the boiler and accessories too much. No combustibles can be placed around the boiler. Do not use oil and water to smother the boiler. The boiler should normally be installed in a separate boiler room. The new gas-fired boiler room should not be connected to the house. The boiler room shall not be connected to Class A, Class B and Category C fire hazard rooms using flammable liquids. If connected to other production plants, the application firewall is separated.

5. The fire resistance grade and fire protection requirements of the boiler house building shall comply with the requirements of the Code for Fire Protection of Building Design and the Code for Fire Protection Design of High-rise Civil Buildings. The ground of the gas steam boiler room should be flat, non-flammable, no water accumulation, and the foundation load should meet the requirements. The power supply voltage of the gas steam boiler room should be stable to avoid causing the electrical components to burn out. If the voltage is unstable, it is recommended to install a voltage regulator. Ventilation equipment should be installed in the boiler room, and the boiler should be kept at room temperature below 50 °.

Free Chat

About Us

Contact Us