2Th Oil Heating Steam Boiler

2Th Oil Heating Steam Boiler

The scaling of gas-fired 2th heating steam boiler not only reduces the thermal efficiency of the boiler, but also increases the temperature of the heating surface of the boiler, causes damage to the heating surface, and even causes the explosion accident of the boiler. Therefore, the use of soft water treatment equipment, strictly according to the process operation of boiler feed water softening treatment equipment, control boiler feed water quality, can delay the formation of the scale. At the same time, it is very important to control the boiler scale in real time, master the boiler scale and clean the scale if necessary. Because the temperature of the gas-steam boiler body and the steam-water heat pipe system is higher than the air temperature in the boiler room, some of the heat is emitted through radiation and convection into the surrounding air. This becomes a loss of heat. Boiler Therefore, the heat loss should be reduced when the heat insulation and heat pipe system of the boiler are damaged or leakage is discovered. The increase in noise from gas-fired steam boiler burners is mainly due to the closure of the valve or insufficient oil intake in the oil path, blockage of the oil filter, or because of low inlet temperature, high viscosity or oil on the pump. Too high temperature; oil pump failure; fan motor bearing damage; due to dirty turbine impeller, the equipment is too loud. This failure occurs when a gas-fired boiler is in use and is not easy to atomize (heavy oil) because of the high viscosity of the oil; it is also due to cyclone and jet The distance between the nozzles is inappropriate; in addition, because the burner is worn or dirty; it is also due to the excessive heating temperature of the spare fuel tank, resulting in steam pumping the oil pump out of the oil pump; or because the oil in the oil boiler is hydrated. Gas steam boiler feed water contains a variety of impurities and calcium, magnesium and other scaling substances, the boiler will inevitably expand. The thermal conductivity of the scale is very low, so once the surface is polluted by the hot surface, the exhaust temperature of the boiler will increase, and the heat loss of the exhaust gas will increase due to the increase of the thermal resistance. The experimental data show that the heat loss of waste gas will be increased by about 2%-4% when 1mm oxide is formed on the heating surface of boiler. The thicker the scale on the heating surface of the boiler, the greater the thermal resistance, and the lower the thermal efficiency of the boiler.

The working principle of 2th heating steam boilers and steam boilers for industrial structural features has brought great convenience, steam boilers led to the development of the times, the following small series to introduce you to the structural characteristics and working principle of steam boilers. Steam boiler is producing steam-based machines, people use a lot, but many of its structure and working principle are not fully aware of, it is the use of volume and pressure water tube steam boilers coal, oil and natural gas are less restrictive , I would like to have a lot of space, but also easy to arrange, in the form of a variety of steam boilers. Water in the steam drum is heated into steam, the heat emitted by the fire in the furnace, is the principle of steam steam boiler. Steam boiler works: 1, heat generated by burning coal in the furnace, the heat transfer by radiation is first absorbed waterwall waterwall Boiling water, a large amount of steam into the drum for water separation (except the DC furnace), separated saturated steam enters the superheater, and continues to absorb the furnace top horizontal flue by means of radiation, convection, heat of the flue gas flue of the tail, and the superheated steam to reach the required operating temperature. Generating steam boilers are generally provided with a reheater, it is used to heat the steam through the high pressure cylinders acting reheater go out of the reheat steam, the low pressure cylinder to continue to generate power. 2, when the pulverized coal fired boiler work, the center position of the flame will impact the amount of evaporation, generally, the lower the evaporation flame kernel, the flame kernel high evaporation amount is small, the center position of the flame will also affect the reheat steam or superheated steam temperature, generally lower the center of the flame in particular superheated steam is then superheated steam temperature to be low, otherwise higher. 3, the arrangement of the burner, pulverized coal fired boiler on, the current embodiment there are opposed wall, more Tangentially combustion, combustion bis Tangentially the like, each have their own characteristics, can not be applied because the same furnace at the same time several above-mentioned arrangement, the steam still can not directly affect the conclusion. Steam boiler structural characteristics: 1, the steam boiler body welding: the main welding using advanced submerged arc welding process, welding quality assurance. All welds were 100% primary radiation detection according to the "Steam Steam Boiler Safety Technology Supervision", according to the eligibility criteria Ⅱ pole. 2, a horizontal steam boiler combustion three return all wet back structure. 3, before steam boiler, after the smoke box sealed with high temperature are graphite asbestos material, a reliable seal, to ensure that the steam boiler flue gas does not leak when run under a slight positive pressure conditions. 4, pipe thread: the second backhaul convection heating surface of the steam boiler, we used a threaded pipe, enabling the efficient heat transfer. Enhanced heat transfer, thermal efficiency of the steam boiler, a threaded tubular light pipe is equal to 2.4. Fluid flow within the tube wall near the fluid flow velocity is very low, the presence of fluid at the wall boundary layer is called, when the thermal resistance in series of several heat transfer water into the flue gas in the outer tube, the boundary layer the maximum thermal resistance, but the boundary layer is thin, as long as the boundary layer of little disturbance, as in an ordinary pressure in a pipe wall to the boss, the disturbance of the boundary layer, will greatly reduce the thermal resistance, is effective threaded pipe one way. 5, to make the system more energy efficient, continuous adjustment using the water supply, to avoid frequent pump start. During the period, the three-pass water smoke tube leaving a wide space, the pot to ensure natural circulation of water flow. 6, the body safety devices: at the rear of the steering steam boiler chamber is provided built-proof door, the steam boiler ignition and running, if the furnace gas deflagration occurs: timely relief, preventing the furnace deflagration, safe and reliable; as built after take-off will not hurt.

If there is damage in the supposed gas-fired? Detailed inspection is important, as the key oil regulation. According to the conditions and time management, gas-fired, people can effectively damage inspection program. The application of oil, people strictly control the particle size of coal and dolomite. Should strictly control the particle size of bed material. Should be addressed furnace waste. To be able to solve the waste furnace after discharge. Natural gas boiler should be installed in areas where the application of calories, easy to install. Heating pipe can not be too long. It should have a good cable jacket. Water piping for an output from moderate to tail skew. Water resources to be equipped with a pressure regulating valve. As sewage gas, natural gas boiler chimney should widen to the outside, a heating furnace entrance width 1.5 to 2M. If you want to reduce the harm to the water wall tube can be appropriately regulate air pressure and wind speed and reasonable to reduce damage to the water wall. Inspection time is generally standby shutdown or shutdown condition. To check top head comprising the furnace wall is damaged, leakage of the furnace airtight and smoke. In the damaged condition requires immediate repair and welding, in order to ensure that no problem in the operation of 2th heating steam boilers. Typically, before the ignition of gas-fired, fossil fuels must be added the charge in the combustion chamber, fossil energy and raw material-circulating bed material and gas in the wind, the strength and intensity of the flow down completely integrated. Bottom wind equipment, up for the core area. Exercise our powers in a ring outside the region along the furnace wall water swimming down, thus increasing the waiting time of coal particles in the furnace. Mineral particles, many of the ash and soot particles with a lot of fly ash, this resulting in rapid deterioration of the waterwall tubes continuously, so that damage to the wall thickness becomes soft, resulting in damage.

In recent years, Hebei Province People's Government to respond positively to Blue Sky Battle action plan promulgated by the state, and all of 35t / h coal-fired boiler and below in the Hebei province out of the transformation process. First Hospital of Baoding respond positively to the call of the provincial government, eliminate serious pollution of the original coal-fired boiler hospital, citing energy saving 2th heating steam boiler to natural gas as raw material. After a series of market research, WNS Series Split hospital condensing gas boiler boiler other fast soft spot.

Free Chat

About Us

Contact Us